Re: Network-related Jaguar problems with my G4 Cube
Re: Network-related Jaguar problems with my G4 Cube
- Subject: Re: Network-related Jaguar problems with my G4 Cube
- From: Smith Kennedy <email@hidden>
- Date: Thu, 2 Jan 2003 13:45:42 -0700
FWIW, one of my co-workers just had the same thing happen to a PowerMac
G4.
On Thursday, January 2, 2003, at 11:43 AM, Smith Kennedy wrote:
Hi,
This is network-related, and programming related, in a way. Just hear
me out! :-)
I have a G4 Cube I use as a test box at work. I have a number of
partitions on it, and I use ASR to image those partitions with
whatever version of the OS I need to do some testing. This is
probably a pretty typical setup. The original graphics card died (bad
VRAM), so I did what seems to be a fairly typical swap, and installed
a GForce2 card from another system (swapped the PCI slot plate with
the one from the original Cube graphics card). Other than that it is
totally unmodified.
The wacky thing is that I have had the worst time getting Jaguar to
install on this system. I have been using CDs burned from the 6C115
images available on the ADC seed site, and also from the Jaguar CDs
sent out with the ADC mailing. I have used both CD-RWs and CD-Rs for
the media on which I burn the Jaguar disk images. Disk 1 always
installs just fine, and the system restarts, but that is where weird
things start to happen. Here are the several scenarios I have
observed. It is the second one that seems network-related. Hopefully
this sounds familiar to someone at Apple.
CD-RW Install Disk:
---------------------------
Once it restarts, the system only starts for a very short period of
time, then the screen goes gray and a funny message is shown that says
"You need to restart your system", and the power button graphic
(circle with a line sticking out of the top), and then at the bottom
it says FF:FF:FF:FF:FF:FF (the length of this may be incorrect, but it
is all Fs). The firmware is 4.1.9, and I have probably reset the PRAM
about 58 times since the firmware update.
CD-R Disk or Jaguar CD:
---------------------------------
Boots fine, but then hangs before the intro app runs (movie with the
water globs, ambient music, registration and initial setup assistant).
Just staring at a blank blue screen. **BUT**, if I let it get to
this stage, and then unplug the LAN cable from the wall, everything
starts to move again, and the intro app runs. It is like it is
waiting for something. But after I complete the install with the LAN
cable unplugged, the system will behave normally if the system stays
off the LAN. When I do plug it in, lots of stuff starts to go > haywire:
- most of the System Preferences don't work (greyed out, and ones that
aren't don't save any changes)
- checking the Startup Disk System Preferences panel will hang System
Preferences
- Running NetInfo Manager, no databases will be available
- Checking the "Sharing" System Preferences panel, all the sharing
mechanisms are disabled (greyed out). On the right, it says that the
"Cupertino Server" is on. I don't know what that is, but I bet there
are people in Cupertino that know. ;-)
Any Install Disk onto External Disk:
----------------------------------------------
I also tried installing Jaguar on an external FireWire disk from
another computer (iMac G4), and then booting the Cube from that
external disk. All is cool until I plug in the LAN cable.
Does any of this sound familiar to anybody? It sounds to me like some
kind of wacky problem with DHCP or NetInfo. But I haven't seen this
behavior on any of my other systems (B&W G3, TiBook).
TIA,
Smith
_______________________________________________
macnetworkprog mailing list | email@hidden
Help/Unsubscribe/Archives:
http://www.lists.apple.com/mailman/listinfo/macnetworkprog
Do not post admin requests to the list. They will be ignored.
_______________________________________________
macnetworkprog mailing list | email@hidden
Help/Unsubscribe/Archives:
http://www.lists.apple.com/mailman/listinfo/macnetworkprog
Do not post admin requests to the list. They will be ignored.